Nitrogen Generator For Additive Manufacturing

Nitrogen Generator For Additive Manufacturing

In additive manufacturing (AM), the quality of metal parts heavily depends on oxygen control inside the print chamber. Residual oxygen leads to powder oxidation and balling, which directly weakens mechanical properties. That’s why a nitrogen generator for additive manufacturing has become a practical solution for many shops. By producing nitrogen on site, you avoid liquid nitrogen tank rental, delivery delays, and purity fluctuations.
Send Inquiry
Product Introduction

In additive manufacturing (AM), the quality of metal parts heavily depends on oxygen control inside the print chamber. Residual oxygen leads to powder oxidation and balling, which directly weakens mechanical properties. That's why a nitrogen generator for additive manufacturing has become a practical solution for many shops. By producing nitrogen on site, you avoid liquid nitrogen tank rental, delivery delays, and purity fluctuations.

 

How it works: PSA and membrane technology for 3D printing environments

For metal additive manufacturing, we mainly use pressure swing adsorption (PSA). Here's the simple version: carbon molecular sieves adsorb oxygen faster than nitrogen. Compressed air enters the adsorber, oxygen gets trapped, and nitrogen passes through to a buffer tank. Two towers alternate - adsorption and regeneration - so you get a continuous nitrogen supply.

For powder bed fusion (SLM, EBM, etc.), PSA is the preferred method, achieving purity up to 99.999%. For laser sintering (SLS) of nylon or polymers where oxidation risk is lower, membrane technology can be a lower-energy alternative. We always recommend choosing based on your material - titanium, aluminum, stainless steel, or polymer powder - and its sensitivity to oxygen.

 

Key specs: purity, flow, temperature, and energy consumption

Here's a quick reference table for our standard models:

Parameter

Range

Note

Nitrogen purity

95% – 99.999%

Adjustable, ±0.1% accuracy

Flow rate (Nm³/h)

1 – 500+

Modular, customizable

Dew point (atm)

≤ -60°C

≤ -70°C optional

Inlet air temp

5°C – 45°C

Pre-treatment required outside range

Power consumption (kW)

0.8 – 110 (depends on flow)

~60% lower than cylinder supply

Noise level

≤75 dB(A)

≤65 dB(A) with soundproof cover

Small units (below 10 Nm³/h) can be integrated directly inside the printer cabinet to reduce piping loss.

 

Technical details that actually affect print quality

A good nitrogen generator for additive manufacturing is more than a purity number. Pay attention to three things:

  1. Purity stability – Fluctuation should be ≤ ±0.2%. If you set 99.99%, actual output should stay between 99.97% and 99.99%, not drop to 99.20%.

  2. Start-up response – Time from power-on to reaching target purity. Our units hit 99.99% within 8 minutes. No long purging between print jobs.

  3. Dew point control – Moisture also causes hydrogen embrittlement, especially for aluminum and titanium. Standard dew point ≤ -60°C; optional ≤ -70°C.

 

Common applications in additive manufacturing 

These generators are already used in several production steps:

  • Metal powder atomization – High-purity nitrogen prevents oxidation during gas atomization.

  • Powder sieving and recovery – Low-oxygen atmosphere reduces fire risk (critical for titanium or magnesium powder).

  • Printer chamber protection – Works with an oxygen analyzer to keep O₂ below 100 ppm.

  • Post-print heat treatment – Prevents surface oxide scale during stress relief annealing.

Whether you work in aerospace, medical implants, molds, or automotive parts - if you print reactive metal powders, the same logic applies.

 

Customization and service

We know that every print shop has a different floor layout, powder type, and compressed air quality. So we offer:

  • Flow customization – Lab scale (0.5 Nm³/h) to industrial (800 Nm³/h)

  • Purity selection – 95%, 99%, 99.9%, 99.99%, 99.999%

  • Mounting options – Skid, container, or wall-mounted for tight spaces

  • Control interface – Modbus RTU standard; Profibus/Profinet optional. Direct integration with printer MES for start/stop interlock.

Service support includes:

  • On-site or remote commissioning (including gas line verification with your printer)

  • Semi-annual performance check (purity, flow, dew point)

  • Molecular sieve life reminder (hour-based, non-AI)

 

Need a payback estimate or a quick selection guide? Ask Shenger Gas.

 

01

02

03

04

05

06

Hot Tags: nitrogen generator for additive manufacturing, China nitrogen generator for additive manufacturing manufacturers, suppliers, factory

Send Inquiry

Home

Phone

E-mail

Inquiry