
Cryogenic Air Separation Unit For Coal Chemical Industry
In coal chemical projects, the gasifier's stable operation depends directly on a continuous, high‑pressure, high‑purity oxygen supply. A properly matched cryogenic air separation unit for coal chemical industry is not just about picking a machine - it's about re‑optimizing the entire air separation thermodynamics for your specific gasification process.
Many engineering firms and plant owners overlook one fact: an ASU can account for 15–25% of a coal chemical plant's total power consumption. But reducing oxygen discharge pressure by just 0.1MPa cuts compressor energy by roughly 6–8%. If the ASU is designed to match the gasifier's inlet pressure from day one - instead of "high pressure then let down" - annual power savings can reach millions of renminbi.
How It Works: Liquefy First, Then Separate by Boiling Point
Cryogenic air separation is conceptually simple: compress, purify and cool air to around –172°C to –196°C until it liquefies, then separate oxygen, nitrogen and argon in a distillation column based on their different boiling points.
-
Oxygen boils at –183°C
-
Nitrogen boils at –196°C
Inside a double‑column system, rising vapor and descending liquid continuously contact each other. Lighter nitrogen concentrates at the top, while heavier oxygen collects at the bottom. For coal chemical applications, oxygen purity typically needs to be ≥99.6%, with argon content controlled if the gasification process is sensitive to inerts.
When Shenger Gas designs a cryogenic air separation unit for coal chemical industry, we pay extra attention to main condenser safety. Coal chemical environments may carry trace hydrocarbons into the ASU. If these accumulate inside the main condenser, risks increase. That's why we use fully submerged main condensers as standard, combined with online total hydrocarbon analyzers and automatic draining logic - an engineering practice that has been widely validated (not unique to Shenger Gas, but we enforce it strictly).
Key Technical Parameters at a Glance
|
Parameter |
Typical Range / Guarantee |
Notes |
|---|---|---|
|
Oxygen purity |
99.6% – 99.8% |
Adjustable per gasifier type; minimum 99.0% |
|
Nitrogen purity |
≤10ppm O₂ (99.999%) |
For ammonia synthesis or pipeline purging |
|
Oxygen flow |
6,000 – 100,000 Nm³/h |
Single train; multiple trains for higher capacity |
|
Nitrogen flow |
1.2 – 2.5 × oxygen flow |
Depends on whether liquid nitrogen wash is required |
|
Cold box operating temp |
–196°C to –172°C |
Warm‑end ΔT ≤5°C; cold‑end ΔT ≤3°C |
|
Specific energy (O₂) |
0.38 – 0.46 kWh/Nm³ O₂ |
Includes main air compressor, booster, expander & internal auxiliaries; excludes cooling tower fans & circulating water pumps |
The energy figures above are based on: discharge pressure 0.5MPaG, cooling water 32°C, 8,000 operating hours/year, near sea level. High‑altitude or hot‑climate sites require recalculation.
Energy Efficiency: Look Beyond the Compressor Nameplate
To evaluate a cryogenic air separation unit for coal chemical industry, don't just read the air compressor's power rating. Look at specific power per liquid oxygen equivalent. If your liquid nitrogen backup system rarely runs, you should minimize the expander's excess refrigeration capacity.
In our design approach, we focus on three verified efficiency targets:
-
Isothermal efficiency – air compressor ≥72%, booster compressor ≥75%
-
Expander efficiency – adiabatic efficiency ≥87% (with brake blower for energy recovery)
-
Heat exchanger margin – main heat exchanger design margin kept at 8–12% (larger margins increase pressure drop unnecessarily)
One more thing often ignored: molecular sieve regeneration energy. We recommend twin‑bed regenerators with a regeneration gas temperature of 220°C ±10°C - no overheating, no wasted steam or electric heating power.
Technical Specification Tips (for Process Design Packages)
If your team is preparing an ASU RFQ for a coal chemical project, make sure these four parameters are clearly defined:
-
Required oxygen discharge pressure – This directly determines compression stages and power. Provide the pressure after the gasifier inlet control valve, not the gasifier's operating pressure.
-
Nitrogen end use – Purging only? 99.9% is fine. Ammonia synthesis feedstock? You need ≤10ppm O₂.
-
Load turndown requirements – Coal chemical plants often follow the gasifier load. Specify how many load changes per day and the ramp rate (we can achieve ≥1.2%/min linear ramping).
-
Local environmental extremes – Summer maximum wet‑bulb, winter minimum dry‑bulb, and altitude. These three numbers decide cooling tower sizing and expander matching.
Custom Engineering: Reverse Design from Mass Balance
When Shenger Gas customizes a cryogenic air separation unit for coal chemical industry, we don't just "change flange sizes." We start from a full Aspen Plus process simulation and match every point:
-
Pressure matching – Cold box oxygen discharge pressure is set directly to the gasifier's required pressure ±0.05MPa. No separate oxygen booster compressor unless the pipeline run is unusually long.
-
By‑product trade‑offs – Do you need liquid argon extraction? A liquid nitrogen backup system? Is liquid oxygen saleable? The choice depends entirely on your payback period requirements.
-
Cold box configuration – Standard steel shell with perlite insulation. For space‑constrained sites, we can design a single integrated cold box with columns, exchangers and piping all inside.
-
Instrumentation & control – Optional DCS one‑button automatic load change logic, reducing operator intervention.
We never claim "we can handle any condition." Instead, we tell you clearly: which parameter changes affect energy consumption, and which cause tray efficiency to drop. That way you make the trade‑off decisions yourself.
Service: We Start When You Send Your Process Data
Shenger Gas service begins the day we receive your process condition sheet - not the day before commissioning.
-
Front‑end – Within 15 working days, we deliver: a mass balance diagram (oxygen, nitrogen, argon compositions and flows), an estimated energy consumption table, and a preliminary equipment layout.
-
During engineering – We provide P&IDs and interlock logic descriptions for joint review by your process and instrument engineers. No "logic doesn't work" surprises on site.
-
After delivery –
On‑site installation guidance (we don't force a bundled service; we can provide only key inspection checkpoints if you prefer)
Operator training (minimum 5 working days, including fault tree analysis)
Remote support interface (main condenser ΔT, expander bearing temperatures, molecular sieve CO₂ breakthrough trends - all can be viewed remotely by authorized persons)
We don't have a "nationwide service network" with 24/7 roadside assistance. But each project gets one dedicated process engineer who stays with it from design through commissioning.
Shenger Gas focuses on cryogenic air separation. For coal chemical applications, we don't sell off‑the‑shelf "universal" units. We design per gasifier type, per client condition. Do we have multiple already‑operating coal chemical references? No - and we're honest about that.
But for every proposal, we provide:
-
A full thermodynamic calculation sheet
-
A design margin statement for every main heat exchanger
-
A hydraulic check for each distillation tray
-
And an energy guarantee (if we miss the guaranteed value, we negotiate contractually)
If you are screening ASU suppliers for a coal chemical project and want a realistic, non‑exaggerated, traceable proposal - contact Shenger Gas Just tell us: your gasifier type, required oxygen flow and pressure, and your local weather conditions. Within two weeks, you will receive a technical solution ready for side‑by‑side comparison.






Hot Tags: cryogenic air separation unit for coal chemical industry, China cryogenic air separation unit for coal chemical industry manufacturers, suppliers, factory, Cryogenic Liquid Nitrogen Plant
You Might Also Like
Send Inquiry










