Containerized PSA Nitrogen Generation System

Containerized PSA Nitrogen Generation System

On-site nitrogen supply depends on matching pretreatment, adsorption cycle and control logic to actual duty. This containerized psa nitrogen generation system is configured for stable purity and straightforward site installation.
Send Inquiry
Product Introduction

The containerized psa nitrogen generation system is designed for plants that need a steady on-site nitrogen supply at a defined flow, purity and pressure. The unit brings together compressed-air pretreatment, dual adsorption towers, carbon molecular sieve, buffer storage, purity analysis and PLC control inside a standard container. Typical capacity is 5–500 Nm³/h, purity 95–99.999%, outlet pressure 0.5–0.8 MPa adjustable, and pressure dew point -40°C or lower depending on configuration. Final performance depends on site temperature, altitude, inlet air quality and duty cycle. Because the unit is configured per project rather than supplied as a fixed catalogue unit, all data should be confirmed before order.

 

System configuration and technical data

A standard scope includes air pretreatment, dual adsorbers with carbon molecular sieve, nitrogen buffer tank, purity analyzer, PLC/HMI, control valves, container with ventilation and access doors, and internal piping and wiring. Optional items include inlet air compressor, refrigerated or desiccant dryer, booster, dew-point meter, flowmeter, remote monitoring, and special voltage or frequency.

Parameter Typical range / note
Capacity 5–500 Nm³/h
Purity 95–99.999%
Outlet pressure 0.5–0.8 MPa, adjustable
Pressure dew point ≤ -40°C; ≤ -60°C optional
Inlet air Oil-free or oil-lubricated with filtration; dew point and particle class per design
Control PLC with HMI; purity alarm and automatic diversion
Container ISO standard; insulation, ventilation, lighting, access doors
Power 220/380/440 V, 50/60 Hz per project
Ambient -10 to 45°C; confirm for high altitude or high temperature

Data are indicative. Final selection is confirmed by flow, purity, pressure, dew point, inlet conditions and site utilities.

 

Applications and selection notes

The unit is used for chemical blanketing, food packaging, electronics assembly, laser cutting, pharmaceutical inerting, metal heat treatment, and oil and gas nitrogen blanketing. For selection, provide required flow and purity together, minimum outlet pressure, maximum dew point, inlet air source, ambient conditions, power supply and installation area. A common mistake is to specify purity alone. If purity is above 99.9%, check purge flow and air-to-nitrogen ratio early; if flow changes widely, review buffer volume and control range. Buyers should ask for a gas balance, utility list, P&ID, layout drawing and factory test report before comparing offers.

 

Installation, operation and maintenance

The containerized psa nitrogen generation system is delivered as a skid-mounted container. Site work normally includes a level foundation, power connection, compressed-air supply, drainage, ventilation clearance and commissioning checks. The PLC runs automatic cycles; operators set purity and pressure from the HMI and review alarm logs. Maintenance includes filter element replacement, valve inspection, analyzer calibration and leak checks. Carbon molecular sieve is normally replaced after 8–10 years, depending on air quality and cycling. Keep inlet air dry and oil-free to protect the sieve and reduce valve fouling.

 

Quality checks and documentation

Factory checks include pressure test, leak test, valve sequence test, analyzer calibration, PLC alarm test and simulated operation. Documentation normally includes general arrangement, P&ID, electrical diagram, utility list, operation manual, maintenance schedule and test records. For export projects, confirm container marking, voltage and frequency, language of HMI and manual, and spare-parts list. These items help project teams verify scope before shipment and plan site commissioning.

 

Shenger Gas supplies the containerized psa nitrogen generation system for industrial projects and provides selection calculation, drawings, factory acceptance testing, documentation and commissioning guidance. Please share your flow, purity, pressure, dew point and site conditions so the technical team can confirm a suitable configuration.

 

01

02

03

04

05

06

Hot Tags: containerized psa nitrogen generation system, China containerized psa nitrogen generation system manufacturers, suppliers, factory

Send Inquiry

Home

Phone

E-mail

Inquiry